Witch with Fogging Claudron
Witch with Fogging Claudron
Bubble, bubble, toil and trouble. There's something brewing in this witch's fogging cauldron and it's about to boil over! She cackles and mutters incantations as she incessantly stirs her evil brew; with her mouth moving, the sound of the cauldron bubbling and her eyes flashing, the overall effect is spellbinding. Cast a spell this Halloween with a lifesize (five feet tall) witch haunting your house. Animated five foot tall Witch has a green complexion and is garbed in a high-quality witch's dress with a spider brooch and feather-trimmed witch's hat. Witch stirs a misting cauldron with a stick. Eyes light and mouth moves to bubbling sounds and cackling laughter. Does not include wireless mic 26 lbs Shipping carton: 31" x 17" x 32" Motion sensor, sound sensor and push button on/off 2 AC adapters included (cauldron has separate connection) 1 ac/dc adapter for mister 24V/AC 20va 1 ac/dc adapter for prop 120V AC input/9V DC output
CONTENTS INSTRUCTIONS CAUTION STORAGE Congratulations! You’re the proud owner of a Gemmy Animated Figure. Please read over the directions carefully before using your new figure. Body 1 piece Head 1 piece Stir Staff 2 pieces Cauldron 1 piece Spider 2 pieces AC/AC Adapter 1 piece AC/DC Adapter 1 piece Input : 120V ~ 60Hz, Output: 9V 2000mA, 24V ~ 20VA 1. Carefully remove figure from box by gently lifting from under its arms. We recommend this action be performed by two people. 2. Place the figure on a stable, secure, and flat surface. 3. Step on button on the back of the base, and gently push down on figure’s shoulders and slowly guide its body upwards to full standing position. Lift up from under its arms to reach full standing locking position. (see illustration 1) 4. Attach figure’s head by aligning the groove and setting head in place. Make sure the latch on the back of the neck locks the head in place. 5. Place Cauldron in front of Figure. Connect the Patch Cord from base of Figure to Cauldron. 6. Connect both pieces of Stir Staff together, and thread connected Stir Staff through holes within Figure’s hands and into provided hole within top of Cauldron. 7. Put one Spider on hat, and put another one on chest. 8. Pour approximately 1 pint of clean, cold water into the Cauldron. (See illustration 2). Make sure water is over the Mister. 9. Two adapters are included, insert each adapter into its corresponding jack, located behind the base, plug the other end of the adapter into a standard wall outlet. (If plugged into an outlet with a power switch, make sure the outlet’s power switch is in the ‘ON’ position.) 10. This power unit is intended to be correctly oriented in vertical or floor mount position. 11. For manual activation, slide the two-way toggle switch to ‘ON’ position and press the button. 12. For motion and sound activation, slide the two-way toggle switch to “SENSOR” position. Simply make a noise or walk by to activate. 13. Adjust volume control to desired position. 14. Unplug adapter when not in use. DO NOT leave the figure plugged in and unattended for long periods of time. Standard safety precautions should be taken as with any electrical device. NOTE: The unit may need to warm-up for up to 3 minutes before fogging action will occur. Please retain this box and packing material for storage of your figure. 1. It is recommended that you store all components of figure in the original packing and box. 2. Lift up on the latch behind the neck to release the head and lift off. ANIMATED FIGURE INSTRUCTIONS Illustration 2 Illustration 1 COLD WATER 29868 英文 042610pg.2 FAQs 3. Step on the button on the back of the base, and gently press down on figure’s shoulders and slowly guide body downwards until you feel it lock into position. 4. Store your Figure in its original packaging and in a dry, cool area. Exposure to the elements can damage the product. As with all electrical devices, exposure to water is a safety hazard. 1. I’ve just set-up my figure, but when I press the button, nothing happens. What’s wrong? First, check to make sure that the Figure’s switch is turned to the ‘ON’ position. Next, ensure the adapter is securely inserted into both the adapter jack and to the wall outlet. Next, make certain the outlet has power. If plugged into an outlet with a power switch, make sure the outlet’s power switch is in the ‘ON’ position. Check and see that the adapter is securely connected to the outlet on the bottom of the Figure. If the Figure still does not work, unplug the adapter from the outlet, reconnect it, and check to see if your Figure will then operate. If the problem is still not resolved, visit our web site for more problem solving tips or to contact a customer service representative. 2. Why is there a two-way toggle switch on my Figure? Your Figure is ready to entertain you and your guests in two different ways: In ‘SENSOR’ mode, the Figure will come to life whenever someone happens to set off the sensor. In ‘ON’ mode, the Figure is active only when you press the button on the base. Simply select the function you want your Figure to perform. SAFETY WARNING: Remove all plastic fasteners and tags. These are part of the packaging and should be discarded. This item is not a toy and should be used for decorative purposes only. For indoor use only.